All Stories

  1. Machinability when micro-slotting nanocomposites

    Article • Key Engineering Materials, October 2018, Trans Tech Publications

    Dr Islam Shyha, Bao Le

  2. An Investigation into the Dependency of Cutting Forces on the Volume Fraction and Fibre Orientation during Machining Composite Materials

    Article • Materials Science Forum, January 2017, Trans Tech Publications

    Dr Islam Shyha

  3. Tool Life Analysis when Turning Ti-6Al-4V Using Vegetable Oil-Based Cutting Fluid

    Article • Materials Science Forum, January 2017, Trans Tech Publications

    Dr Islam Shyha

  4. Optimisation of Weld Overlay Cladding Parameters Using Full-Factorial Design of Experiment

    Article • Materials Science Forum, November 2016, Trans Tech Publications

    Lydia Chan, Dr Islam Shyha

  5. Mechanical, Thermal, and Electrical Properties of Graphene-Epoxy Nanocomposites—A Review

    Article • Polymers, August 2016, MDPI AG

    Dr Islam Shyha

  6. Modeling and experimentation of multi-layered nanostructured graphene-epoxy nanocomposites for enhanced thermal and mechanical properties

    Article • Journal of Composite Materials, July 2016, SAGE Publications

    Dr Islam Shyha

  7. The degradation of mechanical properties in halloysite nanoclay–polyester nanocomposites exposed to diluted methanol

    Article • Journal of Composite Materials, July 2016, SAGE Publications

    Mr. Mohd Shahneel Saharudin, Dr Islam Shyha

  8. Electro-discharge machining of metal matrix composite materials

    Article • Advances in Materials and Processing Technologies, April 2016, Taylor & Francis

    Dr Islam Shyha

  9. Manufacturing at double the speed

    Article • Journal of Materials Processing Technology, March 2016, Elsevier

    Dr Islam Shyha

  10. The degradation of mechanical properties in polymer nano-composites exposed to liquid media – a review

    Article • RSC Advances, January 2016, Royal Society of Chemistry

    Dr Islam Shyha

  11. Use of morphological features of carbonaceous materials for improved mechanical properties of epoxy nanocomposites

    Article • RSC Advances, January 2016, Royal Society of Chemistry

    Dr Islam Shyha

  12. The degradation of mechanical properties due to stress concentration caused by retained acetone in epoxy nanocomposites

    Article • RSC Advances, January 2016, Royal Society of Chemistry

    Dr Islam Shyha

  13. Mould release technologies with regard to concrete surface finish

    Article • Magazine of Concrete Research, January 2016, ICE Publishing

    Dr Islam Shyha, Alan Richardson

  14. The Degradation of Mechanical Properties in Halloysite Nanoclay-Polyester Nanocomposites Exposed in Seawater Environment

    Article • Journal of Nanomaterials, January 2016, Hindawi Publishing Corporation

    Dr Islam Shyha

  15. Machinability analysis when drilling Kovar shape memory alloys

    Article • Advances in Materials and Processing Technologies, October 2015, Taylor & Francis

    Dr Islam Shyha, Dr.-Ing. Islam M. El-Galy

  16. Modelling of Cutting Fibrous Composite Materials: Current Practice

    Article • Procedia CIRP, January 2015, Elsevier

    Dr Islam Shyha

  17. Investigation into the Development of an Additive Manufacturing Technique for the Production of Fibre Composite Products

    Article • Procedia Engineering, January 2015, Elsevier

    Dr Islam Shyha

  18. Machining Unidirectional Composites using Single-Point Tools: Analysis of Cutting Forces, Chip Formation and Surface Integrity

    Article • Procedia Engineering, January 2015, Elsevier

    Dr Islam Shyha

  19. Investigation of Cutting Tools and Working Conditions Effects when Cutting Ti-6al-4V using Vegetable Oil-Based Cutting Fluids

    Article • Procedia Engineering, January 2015, Elsevier

    Dr Islam Shyha

  20. Effect of Varying Mixing Ratios and Pre-Heat Temperature on the Mechanical Properties of Polyurethane (PU) Foam

    Article • Procedia Engineering, January 2015, Elsevier

    Dr Islam Shyha

  21. Workpiece surface integrity and productivity when cutting CFRP and GFRP composites using a CO2 laser

    Article • International Journal of Mechatronics and Manufacturing Systems, January 2014, Inderscience Publishers

    Dr Islam Shyha

  22. An Investigation into CO2 Laser Trimming of CFRP and GFRP Composites

    Article • Procedia Engineering, January 2013, Elsevier

    Dr Islam Shyha

  23. Grinding performance and workpiece integrity when superabrasive edge routing carbon fibre reinforced plastic (CFRP) composites

    Article • CIRP Annals, January 2012, Elsevier

    Dr Islam Shyha

  24. Hole quality assessment following drilling of metallic-composite stacks

    Article • International Journal of Machine Tools and Manufacture, July 2011, Elsevier

    Dr Islam Shyha

  25. The effect of peel ply layer on hole integrity when drilling carbon fibre-reinforced plastic

    Article • Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture, June 2011, SAGE Publications

    Dr Islam Shyha

  26. Drilling of Titanium/CFRP/Aluminium Stacks

    Article • Key Engineering Materials, September 2010, Trans Tech Publications

    Dr Islam Shyha

  27. Effect of laminate configuration and feed rate on cutting performance when drilling holes in carbon fibre reinforced plastic composites

    Article • Journal of Materials Processing Technology, June 2010, Elsevier

    Dr Islam Shyha

  28. Drill geometry and operating effects when cutting small diameter holes in CFRP

    Article • International Journal of Machine Tools and Manufacture, October 2009, Elsevier

    Dr Islam Shyha