All Stories

  1. Segregation of formulated powders in direct compression process and evaluations by small bench-scale testers

    Article • International Journal of Pharmaceutics, November 2023, Elsevier

    Dr Tong Deng

  2. Improved Optimization of a Coextrusion Die with a Complex Geometry Using the Coupling Inverse Design Method

    Article • Polymers, August 2023, MDPI AG

    Dr Tong Deng

  3. Optimising Spread-Layer Quality in Powder Additive Manufacturing: Assessing Packing Fraction and Segregation Tendency

    Article • Processes, July 2023, MDPI AG

    Dr Tong Deng

  4. Electrostatic Charging of Fine Powders and Assessment of Charge Polarity Using an Inductive Charge Sensor

    Article • Nanomanufacturing, June 2023, MDPI AG

    Dr Tong Deng

  5. Noise reduction by using wavelet transform in charge signal acquired from an electrostatic inductive sensor

    Article • Measurement Sensors, June 2023, Elsevier

    Dr Tong Deng, Dr Tariq Hussain

  6. Baseline Tracking in Bipolar Charge Signal Process by Dynamic Time Warping Algorithm

    Article • IEEE Sensors Journal, March 2023, Institute of Electrical & Electronics Engineers (IEEE)

    Dr Tong Deng

  7. Advanced Assessment of Biomass Materials Degradation in Pneumatic Conveying Systems: Challenges and Applications

    Article • Applied Sciences, February 2023, MDPI AG

    Dr Tong Deng

  8. Comparative studies of powder flow predictions using milligrams of powder for identifying powder flow issues

    Article • International Journal of Pharmaceutics, November 2022, Elsevier

    Dr Tong Deng

  9. A new method for assessing powder flowability based on physical properties and cohesiveness of particles using a small quantity of samples

    Article • Powder Technology, January 2022, Elsevier

    Dr Tong Deng

  10. A study of particle adhesion for cohesive powders using a novel mechanical surface energy tester

    Article • Powder Technology, October 2021, Elsevier

    Dr Tong Deng

  11. Correlations between segregation intensity and material properties such as particle sizes and adhesions and novel methods for assessment

    Article • Powder Technology, July 2021, Elsevier

    Dr Tong Deng

  12. An experimental study on free-surface rolling segregation and correlations with angle of repose and particle sphericity

    Article • Powder Technology, February 2021, Elsevier

    Dr Tong Deng

  13. Application of arc-shaped electrostatic sensors for monitoring the flow behaviour at top and bottom section of a pneumatic conveying pipeline

    Article • Measurement Sensors, November 2020, Elsevier

    Dr Tong Deng

  14. Improved inverse design method for thin-wall hollow profiled polymer extrusion die based on FEM-CFD simulations

    Article • The International Journal of Advanced Manufacturing Technology, January 2020, Springer Science + Business Media

    Dr Tong Deng

  15. Optimized Design Method for Profile Extrusion Die Based on NURBS Modeling

    Article • Fibers and Polymers, August 2019, Springer Science + Business Media

    Dr Tong Deng

  16. Development and application of a novel cake strength tester

    Article • Powder Technology, May 2019, Elsevier

    Dr Tong Deng

  17. Wood pellets degradation and influence of high humidity

    Article • Fuel Processing Technology, March 2019, Elsevier

    Dr Tong Deng

  18. CFD simulation model of fine dusts

    Article • The Science of The Total Environment, February 2019, Elsevier

    Dr Tong Deng

  19. Influence of material properties on operation of pneumatic conveying systems

    Article • Powder Technology, December 2016, Elsevier

    Dr Tong Deng

  20. novel instrument bipolar charge

    Article • IET Science Measurement & Technology, August 2016, the Institution of Engineering and Technology (the IET)

    Dr Waseem Kaialy, Dr Tariq Hussain, Dr Tong Deng

  21. Low erosive wear for aligned CNT polymer composites

    Article • Composites Part A Applied Science and Manufacturing, December 2014, Elsevier

    Dr Tong Deng

  22. The effect of CNT orientation on erosive wear resistance of CNT-epoxy based composites

    Article • Carbon, July 2014, Elsevier

    Dr Tong Deng

  23. Erosive wear of pneumatic conveying pipe bends

    Article • Wear, June 2013, Elsevier

    Dr Tong Deng

  24. A novel sensing technique for measurement of magnitude and polarity of electrostatic charge distribution across individual particles

    Article • International Journal of Pharmaceutics, January 2013, Elsevier

    Professor Ali Nokhodchi, Dr Tong Deng, Dr Tariq Hussain

  25. Investigations on air induced segregation of pharmaceutical powders and effect of material flow functions

    Article • Powder Technology, November 2010, Elsevier

    Dr Tong Deng

  26. Understanding particle dynamics in erosion testers—A review of influences of particle movement on erosion test conditions

    Article • Wear, October 2009, Elsevier

    Dr Tong Deng

  27. Evaluation of Particle Degradation Due to High-Speed Impacts in a Pneumatic Handling System

    Article • Particulate Science And Technology, September 2008, Taylor & Francis

    Dr Tong Deng

  28. A comparison of the gas-blast and centrifugal-accelerator erosion testers: The influence of particle dynamics

    Article • Wear, September 2008, Elsevier

    Dr Tong Deng

  29. Comparison between weight loss of bends in a pneumatic conveyor and erosion rate obtained in a centrifugal erosion tester for the same materials

    Article • Wear, January 2005, Elsevier

    Dr Tong Deng

  30. Effect of bend orientation on life and puncture point location due to solid particle erosion of a high concentration flow in pneumatic conveyors

    Article • Wear, January 2005, Elsevier

    Dr Tong Deng

  31. Effect of particle concentration on erosion rate of mild steel bends in a pneumatic conveyor

    Article • Wear, January 2005, Elsevier

    Dr Tong Deng

  32. Prediction of particle rotation in a centrifugal accelerator erosion tester and the effect on erosion rate

    Article • Wear, January 2005, Elsevier

    Dr Tong Deng

  33. The influence of particle rotation on the solid particle erosion rate of metals

    Article • Wear, June 2004, Elsevier

    Dr Tong Deng

  34. A model for bend life prediction due to wear in pneumatic conveying systems

    Article • Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering, August 2002, SAGE Publications

    Dr Tong Deng

  35. Influence of particle dynamics on erosion test conditions within the centrifugal accelerator type erosion tester

    Article • Wear, December 2001, Elsevier

    Dr Tong Deng

  36. An investigation of particle dynamics within a centrifugal accelerator type erosion tester

    Article • Wear, January 2001, Elsevier

    Dr Tong Deng

  37. Anomalies in the results obtained from rotating disc accelerator erosion testers: a discussion of possible causes

    Article • Wear, December 1999, Elsevier

    Dr Tong Deng