All Stories

  1. Observation of Tribological Fatigue Fracture on PEEK Shaft with Artificial Defect under One-Point Rolling Contact by Using 2.5D Layer Method

    Article • Key Engineering Materials, July 2019, Trans Tech Publications

    Ph.D Koshiro Mizobe, Professor Katsuyuki Kida, Dr Hitonobu Koike

  2. Failure Observation of 3D-Printed Thrust Bearing Specimens with Inner Defects in Water Conditions

    Article • Key Engineering Materials, July 2019, Trans Tech Publications

    Ph.D Koshiro Mizobe, Professor Katsuyuki Kida

  3. Subsurface Stress Distribution and Failure of PPS Thrust Bearings under Rolling Contact Fatigue in Water

    Article • Key Engineering Materials, July 2019, Trans Tech Publications

    Professor Katsuyuki Kida

  4. Observation of Crack Growth Behavior of 400μm Cracks in 4.762mm Silicon Nitride Balls under Cyclic Compressive Load

    Article • Key Engineering Materials, July 2019, Trans Tech Publications

    Professor Katsuyuki Kida

  5. Influence of groove shape on rolling contact fatigue of PEEK-PTFE hybrid radial bearings in dry conditions

    Article • MATEC Web of Conferences, January 2019, EDP Sciences

    Professor Katsuyuki Kida

  6. Influence of Furnace-Induction Heating on Hardness Distribution and Retained Austenite in JIS SUJ2 Bearing Steel

    Article • Key Engineering Materials, December 2018, Trans Tech Publications

    Ph.D Koshiro Mizobe, Professor Katsuyuki Kida

  7. Rolling Contact Fatigue Life of 13Cr-2Ni-2Mo Stainless Steels which are Surface Treated by Induction Heating (IH) and Wide Peening Cleaning (WPC)

    Article • Key Engineering Materials, August 2018, Trans Tech Publications

    Professor Katsuyuki Kida, Ph.D Koshiro Mizobe

  8. Failure Observation of 3D-Printed Thrust Bearing Specimens at Cross Section Observations in Dry Conditions

    Article • Key Engineering Materials, August 2018, Trans Tech Publications

    Ph.D Koshiro Mizobe, Professor Katsuyuki Kida

  9. Three-Dimensional Scanning Hall Probe Microscopy for Final Stage of Crack Growth of Chromium Molybdenum Steel SCM440

    Article • Key Engineering Materials, August 2017, Trans Tech Publications

    Professor Katsuyuki Kida

  10. Observation of Fracture Surface of Induction-Heated JIS SUJ2 Bearing Steel under Rotating Bending Fatigue

    Article • Materials Science Forum, August 2017, Trans Tech Publications

    Professor Katsuyuki Kida, Ph.D Koshiro Mizobe

  11. Observation of Furnace-Induction Quenched Microstructure in High Carbon High Chromium Steel

    Article • Materials Science Forum, August 2017, Trans Tech Publications

    Ph.D Koshiro Mizobe, Professor Katsuyuki Kida

  12. Non-Destructive Stress Evaluation of Tool Steel Using Scanning Hall Probe Microscope: Effect of Stress Direction on Three Dimensional Magnetic Fields

    Article • Key Engineering Materials, June 2017, Trans Tech Publications

    Professor Katsuyuki Kida, Ariyasu Yadoiwa, yamada takuto

  13. Fatigue of Low Carbon Alloy Steel (JIS S45C) and a New Method of Fracture Surface Analysis

    Article • Materials Science Forum, March 2017, Trans Tech Publications

    Professor Katsuyuki Kida, Ph.D Koshiro Mizobe

  14. Rolling Contact Fatigue and Static Compression Deformation of UHMWPE thrust bearing in water

    Article • MATEC Web of Conferences, January 2017, EDP Sciences

    Professor Katsuyuki Kida

  15. Effect of Groove Geometry on Rolling Contact Fatigue of PEEK Thrust Bearings in Water

    Article • Materials Science Forum, November 2016, Trans Tech Publications

    Professor Katsuyuki Kida, Ph.D Koshiro Mizobe

  16. Observation of Fatigue Fracture on PEEK Shaft against Alumina Bearing’s Ball under One-Point Rolling Contact

    Article • Materials Science Forum, November 2016, Trans Tech Publications

    Ph.D Koshiro Mizobe, Professor Katsuyuki Kida, Dr Hitonobu Koike

  17. Evaluation of Tribological Thermal Failure on PEEK-PTFE Hybrid Alumina Ball Bearings

    Article • Materials Science Forum, November 2016, Trans Tech Publications

    Ph.D Koshiro Mizobe, Professor Katsuyuki Kida, Dr Hitonobu Koike

  18. Crack Observation of PPS Polymer Thrust Bearings under RCF Test in Water

    Article • Key Engineering Materials, August 2016, Trans Tech Publications

    Professor Katsuyuki Kida

  19. Relationship between Failure and Temperature of PTFE Thrust Bearings under Dry Condition

    Article • Key Engineering Materials, August 2016, Trans Tech Publications

    Professor Katsuyuki Kida

  20. Changes in Magnetic Flux Density Distributions of Chromium Molybdenum Steel (JIS, SCM440) by Slit Opening and Crack Growth

    Article • Key Engineering Materials, August 2016, Trans Tech Publications

    Professor Katsuyuki Kida

  21. Backlash Evaluation of Hybrid UHMWPE-PEEK Bushes in a Small Robot Joint System

    Article • Key Engineering Materials, August 2016, Trans Tech Publications

    Professor Katsuyuki Kida, Ph.D Koshiro Mizobe, Hitonobu Koike, Dr Hitonobu Koike

  22. Effect of New Pocket Design on the Failure of Thrust UHMWPE Bearings in Dry Condition

    Article • Key Engineering Materials, August 2016, Trans Tech Publications

    Ph.D Koshiro Mizobe, Professor Katsuyuki Kida

  23. Rolling Contact Fatigue Observation of Radial PPS Bearings under Dry Condition

    Article • Key Engineering Materials, August 2016, Trans Tech Publications

    Ph.D Koshiro Mizobe, Professor Katsuyuki Kida

  24. Observation of Retained Austenite Amount of Repeatedly Induction Heated SUJ2 Bearing Steels

    Article • Materials Science Forum, August 2016, Trans Tech Publications

    Ph.D Koshiro Mizobe, Professor Katsuyuki Kida

  25. Effect of Repeated Quenching on Rolling Contact Fatigue Properties of JIS SUJ2 Bearing Steel

    Article • Materials Science Forum, August 2016, Trans Tech Publications

    Ph.D Koshiro Mizobe, Professor Katsuyuki Kida

  26. Relationship between Solid Lubricant Layer and Friction Coefficient of PPS Races-PTFE Retainer Hybrid Thrust Bearings under Dry Condition

    Article • Advanced Materials Research, May 2015, Trans Tech Publications

    Professor Katsuyuki Kida, Ph.D Koshiro Mizobe

  27. An Image Analyzing Method by a Homology Concept for Fracture Surfaces

    Article • Advanced Materials Research, May 2015, Trans Tech Publications

    Professor Katsuyuki Kida

  28. Application of the Betti Number to Prior Austenite Grain Size Analysis of Repeatedly Quenched Steel Based on the Homology Method

    Article • Advanced Materials Research, May 2015, Trans Tech Publications

    Professor Katsuyuki Kida, Ph.D Koshiro Mizobe

  29. Relation between the Betti Number of Fatigue Fracture Surfaces and Stress Intensity Factors of Low Carbon Steel (JIS, S45C)

    Article • Advanced Materials Research, May 2015, Trans Tech Publications

    Professor Katsuyuki Kida, Ph.D Koshiro Mizobe

  30. The Betti Number of Prior Austenite Structure of Repeated Quenching Bearing Steels (JIS, SUJ2)

    Article • Advanced Materials Research, December 2014, Trans Tech Publications

    Professor Katsuyuki Kida, Ph.D Koshiro Mizobe

  31. Fatigue characterisation of HIP-silicon nitride under shear stress: effect of stress ratio on surface crack growth in silicon nitride square bar under cyclic torsion

    Article • Materials Research Innovations, August 2014, Taylor & Francis

    Professor Katsuyuki Kida

  32. Surface crack and wear of PPS polymer thrust bearings under rolling contact fatigue in water

    Article • Materials Research Innovations, August 2014, Taylor & Francis

    Professor Katsuyuki Kida

  33. Observation of rolling contact fatigue of induction heated 13Cr–2Ni–2Mo stainless steel under reciprocating motion

    Article • Materials Research Innovations, August 2014, Taylor & Francis

    Professor Katsuyuki Kida

  34. Changes in three-dimensional magnetic fields of star shaped JIS-SKS93 plates embedded in clear acrylic cold mounting resin under tensile loads

    Article • Materials Research Innovations, March 2014, Taylor & Francis

    Professor Katsuyuki Kida

  35. Relationship between repeatedly quenching and fisheye cracks around TiN and Al2O3 inclusions in high carbon bearing steel

    Article • Materials Research Innovations, March 2014, Taylor & Francis

    Professor Katsuyuki Kida, Dr Hitonobu Koike

  36. Three-dimensional magnetic microscopy of early stage fatigue in WMZ of low carbon steel plates (JIS-SS400)

    Article • Materials Research Innovations, March 2014, Taylor & Francis

    Professor Katsuyuki Kida

  37. Three-dimensional observation of magnetic fields in alloy tool steel under spherical Hertzian contact

    Article • Materials Research Innovations, March 2014, Taylor & Francis

    Professor Katsuyuki Kida