All Stories

  1. Influence of contact pressure and sliding speed dependence on the tribological characteristics of an activated carbon-epoxy composite derived from palm kernel under dry sliding conditions

    Article • Friction, May 2018, Tsinghua University Press

    Dr Mohd Fadzli Bin Abdollah

  2. Frictional wear stability mechanisms of an activated carbon composite derived from palm kernel by phase transformation study

    Article • Industrial Lubrication and Tribology, November 2017, Emerald

    Dr Mohd Fadzli Bin Abdollah

  3. A brief review on the wear mechanisms and interfaces of carbon based materials

    Article • Composite Interfaces, September 2017, Taylor & Francis

    Dr Mohd Fadzli Bin Abdollah

  4. Statistical models for predicting wear and friction coefficient of palm kernel activated carbon-epoxy composite using the ANOVA

    Article • Industrial Lubrication and Tribology, September 2017, Emerald

    Dr Mohd Fadzli Bin Abdollah

  5. The effect of dimple size on the tribological performances of a laser surface textured palm kernel activated carbon-epoxy composite

    Article • Industrial Lubrication and Tribology, September 2017, Emerald

    Dr Mohd Fadzli Bin Abdollah

  6. Tribological performance of low blend decanter cake biodiesel

    Article • Industrial Lubrication and Tribology, May 2017, Emerald

    Dr Mohd Fadzli Bin Abdollah

  7. Optimization of friction properties of kenaf polymer composite as an alternative friction material

    Article • Industrial Lubrication and Tribology, March 2017, Emerald

    Dr Mohd Fadzli Bin Abdollah

  8. Effect of hexagonal boron nitride nanoparticles as an additive on the extreme pressure properties of engine oil

    Article • Industrial Lubrication and Tribology, June 2016, Emerald

    Dr Mohd Fadzli Bin Abdollah

  9. Effect of Diluted Nano-Oil on the Anti-Wear and Friction Properties

    Article • Advanced Materials Research, January 2016, Trans Tech Publications

    Dr Mohd Fadzli Bin Abdollah

  10. Friction Properties of Waste Cooking Oil with Banana Peel Broth

    Article • Advanced Materials Research, January 2016, Trans Tech Publications

    Dr Mohd Fadzli Bin Abdollah

  11. Thermal Conductivity and Latent Heat Properties of Microencapsulated Phase Change Material (μPCM)/Multiwall Carbon Nanotube (MWCNT) Composites for EVs Application

    Article • Advanced Materials Research, January 2016, Trans Tech Publications

    Dr Mohd Fadzli Bin Abdollah

  12. The potential of hBN nanoparticles as friction modifier and antiwear additive in engine oil

    Article • Mechanics & Industry, October 2015, EDP Sciences

    Dr Mohd Fadzli Bin Abdollah

  13. The Effects of Voltage Flow and pH Value in Alkaline Electrolyser System to Performance

    Article • Applied Mechanics and Materials, July 2015, Trans Tech Publications

    Dr Mohd Fadzli Bin Abdollah

  14. The Storage Effect on Fuel Properties and Emission for Variety Biodiesel Blends

    Article • Applied Mechanics and Materials, July 2015, Trans Tech Publications

    Dr Mohd Fadzli Bin Abdollah, Ms Humairak Yusof

  15. Tensile Behavior of Polypropylene Reinforced with Comminutes Extracted from Out-of-Condition Aerospace Grade Carbon Fiber Prepreg Waste

    Article • Applied Mechanics and Materials, May 2015, Trans Tech Publications

    Dr Mohd Fadzli Bin Abdollah

  16. The Implementation of Product Architecture in Developing Conceptual Design for Passive Grease Trap

    Article • Applied Mechanics and Materials, May 2015, Trans Tech Publications

    Dr Mohd Fadzli Bin Abdollah

  17. Selection and verification of kenaf fibres as an alternative friction material using Weighted Decision Matrix method

    Article • Materials & Design (1980-2015), February 2015, Elsevier

    Dr Mohd Fadzli Bin Abdollah

  18. Improving Engine Oil Properties by Dispersion of hBN/Al2O3 Nanoparticles

    Article • Applied Mechanics and Materials, July 2014, Trans Tech Publications

    Dr Mohd Fadzli Bin Abdollah

  19. Experimental Study on Friction and Wear Behaviors of Ball Bearings under Gas Lubricated Conditions

    Article • Jurnal Teknologi, March 2014, Penerbit UTM Press

    Dr Mohd Fadzli Bin Abdollah

  20. Effect of hBN/Al2O3 Nanoparticle Additives on the Tribological Performance of Engine Oil

    Article • Jurnal Teknologi, March 2014, Penerbit UTM Press

    Dr Mohd Fadzli Bin Abdollah

  21. Materials selection for eco-aware lightweight friction material

    Article • Mechanics & Industry, January 2014, EDP Sciences

    Dr Mohd Fadzli Bin Abdollah

  22. Mechanical and Morphological Properties of Polypropylene/Epoxidized Natural Rubber Blends at Various Mixing Ratio

    Article • Procedia Engineering, January 2013, Elsevier

    Dr MOHD ASYADI AZAM, Dr Mohd Fadzli Bin Abdollah

  23. Design Optimization of Thermal Management System for Electric VehicleUtilizing CFD Analysis, DFMEA and CES

    Article • Procedia Engineering, January 2013, Elsevier

    Dr Mohd Fadzli Bin Abdollah

  24. Frictional Behavior of Bearing Material under Gas Lubricated Conditions

    Article • Procedia Engineering, January 2013, Elsevier

    Dr Mohd Fadzli Bin Abdollah

  25. Elastohydrodynamics Lubrication for Bio-based Lubricants in Elliptical Conjunction

    Article • Procedia Engineering, January 2013, Elsevier

    Dr Mohd Fadzli Bin Abdollah

  26. Preliminary Study of CST in Malaysia based on Field Optical Efficiency

    Article • Procedia Engineering, January 2013, Elsevier

    Dr Mohd Fadzli Bin Abdollah

  27. Optimization of Tribological Performance of hBN/AL2O3Nanoparticles as Engine Oil Additives

    Article • Procedia Engineering, January 2013, Elsevier

    Dr Mohd Fadzli Bin Abdollah

  28. Comparison of Soot Particle Movement based on Crank Angle

    Article • Procedia Engineering, January 2013, Elsevier

    Dr Mohd Fadzli Bin Abdollah, Dr Wan Mohd Faizal Wan Mahmood

  29. Deformation–wear transition map of DLC coating under cyclic impact loading

    Article • Wear, January 2012, Elsevier

    Dr Mohd Fadzli Bin Abdollah

  30. Future Developments of a Deformation - Wear Transition Map of DLC Coating

    Article • Tribology Online, January 2012, Japanese Society of Tribologists

    Dr Mohd Fadzli Bin Abdollah

  31. The Effect of Maximum Normal Impact Load, Absorbed Energy, and Contact Impulse, on the Impact Crater Volume/Depth of DLC Coating

    Article • Tribology Online, January 2011, Japanese Society of Tribologists

    Dr Mohd Fadzli Bin Abdollah

  32. Phase transformation studies on the a-C coating under repetitive impacts

    Article • Surface and Coatings Technology, October 2010, Elsevier

    Dr Mohd Fadzli Bin Abdollah