All Stories

  1. Spark plasma sintering versus hot pressing – densification, bending strength, microstructure, and tribological properties of Ti5Al2.5Fe alloys

    Article • Powder Metallurgy, February 2018, Taylor & Francis

    Dr RIDVAN YAMANOGLU

  2. Production and mechanical properties of Ti–5Al–2.5Fe–xCu alloys for biomedical applications

    Article • Biomedical Materials, January 2018, Institute of Physics Publishing

    Dr RIDVAN YAMANOGLU

  3. Failure analysis of wire-breaks in aluminum conductor production and investigation of early failure reasons for transmission lines

    Article • Engineering Failure Analysis, January 2018, Elsevier

    Dr RIDVAN YAMANOGLU

  4. Enhanced surface properties of iron by in situ hard nickel coating

    Article • Materials Testing, February 2016, Carl Hanser Verlag

    Dr RIDVAN YAMANOGLU

  5. Mechanical properties of hypoeutectic Al-Ni alloys with Al3Ni intermetallics

    Article • Materials Testing, February 2016, Carl Hanser Verlag

    Dr RIDVAN YAMANOGLU

  6. In Situ Aluminum Alloy Coating on Magnesium by Hot Pressing

    Article • Acta Metallurgica Sinica (English Letters), July 2015, Springer Science + Business Media

    Dr RIDVAN YAMANOGLU

  7. Investigation of corrosion and mechanical properties of Al–Cu–SiC–xNi composite alloys

    Article • Materials & Design (1980-2015), July 2014, Elsevier

    Dr RIDVAN YAMANOGLU

  8. Characterisation of nickel alloy powders processed by spark plasma sintering

    Article • Powder Metallurgy, April 2014, Taylor & Francis

    Dr RIDVAN YAMANOGLU

  9. Production and characterization of Al-xNi in situ composites using hot pressing

    Article • Journal of Mining and Metallurgy Section B Metallurgy, January 2014, National Library of Serbia

    Dr RIDVAN YAMANOGLU

  10. Effect of nickel on microstructure and wear behaviour of pure aluminium against steel and alumina counterfaces

    Article • International Journal of Cast Metals Research, October 2013, Maney Publishing

    Dr RIDVAN YAMANOGLU

  11. Effect of heat treatment on erosive wear behaviour of Ti6Al4V alloy

    Article • Materials Science and Technology, September 2013, Taylor & Francis

    Egemen Avcu, Dr RIDVAN YAMANOGLU

  12. Sintering and microstructure characteristics of 42CrMo4 steel processed by spark plasma sintering

    Article • Metals and Materials International, September 2013, Springer Science + Business Media

    Dr RIDVAN YAMANOGLU

  13. Effect of heat treatment on the tribological properties of Al–Cu–Mg/nanoSiC composites

    Article • Materials & Design (1980-2015), August 2013, Elsevier

    Dr RIDVAN YAMANOGLU

  14. Effect of heat treatment conditions on microstructure and wear behaviour of Al4Cu2Ni2Mg alloy

    Article • Transactions of Nonferrous Metals Society of China, July 2013, Elsevier

    Dr RIDVAN YAMANOGLU

  15. Comparative evaluation of densification and grain size of ZnO powder compacts during microwave and pressureless spark plasma sintering

    Article • Advances in Applied Ceramics Structural Functional and Bioceramics, October 2012, SAGE Publications

    Dr RIDVAN YAMANOGLU

  16. Mechanical and wear properties of pre-alloyed molybdenum P/M steels with nickel addition

    Article • Journal of Mining and Metallurgy Section B Metallurgy, January 2012, National Library of Serbia

    Dr RIDVAN YAMANOGLU

  17. Solidification characteristics of atomized AlCu4Mg1-SiC composite powders

    Article • Journal of Mining and Metallurgy Section B Metallurgy, January 2012, National Library of Serbia

    Dr RIDVAN YAMANOGLU

  18. Microstructural investigation of as cast and PREP atomised Ti–6Al–4V alloy

    Article • Powder Metallurgy, December 2011, Taylor & Francis

    Dr RIDVAN YAMANOGLU

  19. Effect of Nickel Addition and Porosity on Fracture Behaviour of Molybdenum Alloyed Powder Metallurgical Steel

    Article • Materials Testing, April 2010, Carl Hanser Verlag

    Dr RIDVAN YAMANOGLU