All Stories

  1. Influence of niobium solutes on the microstructural evolution of nickel during hot working

    Article • Materials Research Express, November 2019, Institute of Physics Publishing

    Professor Lamine Fares

  2. Constitutive Modelling of an Industrial Rolled Sheet for a DIN 1623 St14 (DC04) Steel

    Article • Solid State Phenomena, September 2019, Trans Tech Publications

    Professor Lamine Fares, Oualid Chahaoui, Mr Badreddine Regaiguia

  3. The Avrami Kinetics of Dynamic Recrystallization in Nickel-Niobium Alloys

    Article • Materials Science Forum, December 2018, Trans Tech Publications

    Nedjoua MATOUGUI, Professor Lamine Fares

  4. Influence of Niobium Content on the Hot Mechanical Behavior of Nickel Alloys

    Article • Materials Science Forum, November 2016, Trans Tech Publications

    Professor Lamine Fares

  5. Comparing two treatments for assessing hot ductility behavior of HSLA steels

    Article • steel research international, December 2014, Wiley

    Professor Lamine Fares

  6. A Critical Assessment of Three Usual Equations for Strain Hardening and Dynamic Recovery

    Article • Metallurgical and Materials Transactions A, June 2014, Springer Science + Business Media

    Professor Lamine Fares, Nedjoua MATOUGUI

  7. Influence of niobium solutes on the mechanical behavior of nickel during hot working

    Article • Materials Science and Engineering A, December 2013, Elsevier

    Professor Lamine Fares, Nedjoua MATOUGUI

  8. Mechanical behavior modelisation of heterogeneous cold rolled sheet.

    Article • Metals and Materials International, September 2013, Springer Science + Business Media

    Professor Lamine Fares

  9. An investigation into the effects of conventional heat treatments on mechanical characteristics of new hot working tool steel

    Article • IOP Conference Series Materials Science and Engineering, February 2012, Institute of Physics Publishing

    Professor Lamine Fares

  10. Deformation behavior of a Nb-Ti-V microalloyed steel to achieve the HSLA X80 grade by simulation with a torsion test and pilot hot rolling mill

    Article • Revue de Métallurgie, January 2012, EDP Sciences

    Professor Lamine Fares

  11. An Investigation on the Usefulness and Performance of New Hot Working Tool Steel by Nitrocarburizing Process

    Article • e-Journal of Surface Science and Nanotechnology, January 2012, Surface Science Society Japan

    Professor Lamine Fares

  12. Erratum: An Investigation on the Usefulness and Performance of New Hot Working Tool Steel by Nitrocarburizing Process [e-J. Surf. Sci. Nanotech. Vol. 10, pp. 1-11 (2012)]

    Article • e-Journal of Surface Science and Nanotechnology, January 2012, Surface Science Society Japan

    Professor Lamine Fares

  13. Effects of gas carbonitriding process on surface characteristics of new hot working tool steel

    Article • Surface Engineering, September 2011, Taylor & Francis

    Professor Lamine Fares

  14. Surface Characteristics Analysis of Gas Carburized New Hot Working Tool Steel

    Article • e-Journal of Surface Science and Nanotechnology, January 2011, Surface Science Society Japan

    Professor Lamine Fares

  15. Monoclinic effects and orthotropic estimation for the behaviour of rolled sheet

    Article • Journal of Materials Science, October 2010, Springer Science + Business Media

    Professor Lamine Fares

  16. The results revealed a Fe2O3 layer that enhanced both wear and corrosion resistance.

    Article • Surface and Interface Analysis, July 2009, Wiley

    Professor Lamine Fares

  17. Surface characteristics analysis of nitrocarburized (Tenifer) and carbonitrided industrial steel AISI 02 types

    Article • Surface and Interface Analysis, November 2008, Wiley

    Professor Lamine Fares

  18. Relation microstructure-endommagement d’un acier à outil de travail à froid

    Article • European Journal of Control, September 2004, Lavoisier

    Professor Lamine Fares

  19. Relation microstructure-endommagement d’un acier à outil de travail à froid

    Article • European Journal of Control, September 2004, Lavoisier

    Professor Lamine Fares

  20. Étude expérimentale de l'hétérogénéité de la déformation lors de l'essai de la compression plane de monocristauxExperimental study of the inhomogeneous deformation in the plane strain compression test of single crystals

    Article • Mécanique & Industries, December 2002, Elsevier

    Professor Lamine Fares

  21. Rôle de la précipitation sur l'oxydation d'un alliage Fe-Cr-Al dans l'air à 1100° CThe role of precipitation in the oxidation of an Fe-Cr-Al alloy in air at 1100° C

    Article • Annales de Chimie Science des Matériaux, August 2002, Elsevier

    Professor Lamine Fares

  22. Modélisation mécanique de l’essai de compression plane de monocristaux

    Article • Revue de Métallurgie, May 1995, EDP Sciences

    Professor Lamine Fares