All Stories

  1. Effect of Latent Heat of Aluminum Alloys on Bonding between Strips in Clad Strip Cast by a Twin-Roll Caster

    Article • Key Engineering Materials, June 2019, Trans Tech Publications

    Toshio Haga

  2. 600 mm-Wide Strip Casting Using Single Roll Caster Equipped with Scraper

    Article • Key Engineering Materials, June 2019, Trans Tech Publications

    Toshio Haga

  3. Forming of Small Projection on Roll-Cast A356 Strip by Cold Rolling and Small Groove on PET Plate Using A356 Die

    Article • Key Engineering Materials, June 2019, Trans Tech Publications

    Toshio Haga

  4. Investigation of Side-Dam Plate in Single-Wheel Caster for Casting Rods

    Article • Key Engineering Materials, June 2019, Trans Tech Publications

    Toshio Haga

  5. Fabrication of Lotus Type Porous Ingots Using the Core-Bar Pulling Method

    Article • Solid State Phenomena, January 2019, Trans Tech Publications

    Toshio Haga

  6. Fabrication of Thin Heat Sinks by the Die Casting of Semisolid Al-25%Si

    Article • Solid State Phenomena, January 2019, Trans Tech Publications

    Toshio Haga

  7. Hot Forging of Roll-Cast Magnesium Alloys with High Aluminum Content

    Article • Key Engineering Materials, November 2018, Trans Tech Publications

    hirawatari sueji, Toshio Haga, HISAKI WATARI

  8. Production of Clad Metals Using the Melts-Kiss Method

    Article • Key Engineering Materials, October 2018, Trans Tech Publications

    Toshio Haga

  9. Roll Casting of Al-40%Sn-1%Cu Strip

    Article • Defect and Diffusion Forum, January 2018, Trans Tech Publications

    Toshio Haga

  10. Prevention of Solidification of Al-40%Sn-1%Cu in Melt Pool on the Roll Casting Using Unequal Diameter Twin Roll Caster

    Article • Defect and Diffusion Forum, January 2018, Trans Tech Publications

    Toshio Haga

  11. Die-casting of product with thin fins by Al-25%Si

    Article • Advances in Materials and Processing Technologies, December 2017, Taylor & Francis

    Toshio Haga

  12. Semisolid Strip Casting of Aluminum Alloy by a Twin Roll Caster Equipped with a Channel Scraper

    Article • Key Engineering Materials, August 2017, Trans Tech Publications

    Toshio Haga

  13. Effect of Casting Conditions on Fabrication of Lotus Type Holes in Ingot Cast by Core-Bar Pulling Method

    Article • Key Engineering Materials, August 2017, Trans Tech Publications

    Toshio Haga

  14. Semi-Continuous Caster for an Aluminum Alloy Plate

    Article • Materials Science Forum, August 2017, Trans Tech Publications

    Toshio Haga

  15. Roll Casting of 400 mm Width Al-40%Sn-1%Cu Clad Strip

    Article • Materials Science Forum, August 2017, Trans Tech Publications

    Toshio Haga

  16. Casting of aluminum alloy clad strip by an unequal diameter twin-roll caster equipped with a scraper

    Article • Advances in Materials and Processing Technologies, June 2017, Taylor & Francis

    Toshio Haga

  17. Casting of Clad Strip of Al-SiCp, Magnesium Alloy Hard-Brittle Light Material by a Twin Roll Caster

    Article • Materials Science Forum, March 2017, Trans Tech Publications

    Toshio Haga

  18. Gravity Casting of Al-30vol%SiCp Plate

    Article • Materials Science Forum, March 2017, Trans Tech Publications

    Toshio Haga

  19. roll casting

    Article • Applied Mechanics and Materials, July 2015, Trans Tech Publications

    Toshio Haga, Prof. Hisaki Watari

  20. Semisolid Casting of Product with Thin Fins by Using Al-25%Si

    Article • Key Engineering Materials, July 2015, Trans Tech Publications

    Toshio Haga

  21. Fabrication of Ingot with Lotus Type Through-Holes in Semisolid Condition

    Article • Key Engineering Materials, July 2015, Trans Tech Publications

    Toshio Haga

  22. Semi-Solid Die Casting of Al-25%Si

    Article • Solid State Phenomena, September 2014, Trans Tech Publications

    Toshio Haga