Contact

All Stories

  1. Novel design of a coreless axial-flux permanent-magnet generator with three-layer winding coil for small wind turbines

    Article • IET Renewable Power Generation, September 2020, the Institution of Engineering and Technology (the IET)

    Distinguished Professor Jyh-Cheng Yu

  2. Reliability-based Robust Design Optimization for Correlated Variables Using Sequential Surrogate assisted Evolutionary Algorithm

    Article • June 2019, Institute of Electrical & Electronics Engineers (IEEE)

    Distinguished Professor Jyh-Cheng Yu

  3. Optical design optimization of high contrast light guide plate for front light unit

    Article • Microsystem Technologies, January 2019, Springer Science + Business Media

    Distinguished Professor Jyh-Cheng Yu

  4. Evolutionary reliable regional Kriging surrogate for expensive optimization

    Article • Engineering Optimization, April 2018, Taylor & Francis

    Distinguished Professor Jyh-Cheng Yu

  5. Optimum Design of Microridge Deep Drawing Punch Using Regional Kriging Assisted Fuzzy Multiobjective Evolutionary Algorithm

    Article • IEEE Access, January 2018, Institute of Electrical & Electronics Engineers (IEEE)

    Distinguished Professor Jyh-Cheng Yu

  6. Robust design optimisation via surrogate network model and soft outer array design

    Article • International Journal of Production Research, July 2017, Taylor & Francis

    Distinguished Professor Jyh-Cheng Yu

  7. Evolutionary Reliable Regional Kriging Surrogate and Soft Outer Array for Robust Engineering Optimization

    Article • IEEE Access, January 2017, Institute of Electrical & Electronics Engineers (IEEE)

    Distinguished Professor Jyh-Cheng Yu

  8. Evolutionary algorithm using progressive Kriging model and dynamic reliable region for expensive optimization problems

    Article • October 2016, Institute of Electrical & Electronics Engineers (IEEE)

    Distinguished Professor Jyh-Cheng Yu

  9. Optical design and optimization of planar curved LED end-lit light bar

    Article • Applied Optics, August 2014, Optical Society of America (OSA)

    Distinguished Professor Jyh-Cheng Yu

  10. Evolutionary regional network modeling for efficient engineering optimization

    Article • July 2014, Institute of Electrical & Electronics Engineers (IEEE)

    Distinguished Professor Jyh-Cheng Yu

  11. Design of LED edge-lit light bar for automotive taillight applications

    Article • September 2013, SPIE

    Distinguished Professor Jyh-Cheng Yu

  12. Intelligent Optimization of the Replication of Injection Molding Light Guide Plates Using Rapid Mold Surface Inducting Heating

    Article • November 2011, Institute of Electrical & Electronics Engineers (IEEE)

    Distinguished Professor Jyh-Cheng Yu

  13. Modeling analysis of a triaxial microaccelerometer with piezoelectric thin-film sensing using energy method

    Article • Microsystem Technologies, February 2011, Springer Science + Business Media

    Distinguished Professor Jyh-Cheng Yu

  14. A study of power saving LED back light module

    Article • November 2010, SPIE

    Distinguished Professor Jyh-Cheng Yu

  15. Effect of rapid mold surface inducting heating on the replication ability of microinjection molding light-guided plates with V-grooved microfeatures

    Article • Journal of Applied Polymer Science, June 2010, Wiley

    Distinguished Professor Jyh-Cheng Yu

  16. Design optimization of extrusion-blow-molded parts using prediction-reliability-guided search of evolving network modeling

    Article • Journal of Applied Polymer Science, January 2010, Wiley

    Distinguished Professor Jyh-Cheng Yu

  17. Integration of stamper fabrication and design optimization of LCD Light guides using silicon-based microfeatures

    Article • Microsystem Technologies, November 2009, Springer Science + Business Media

    Distinguished Professor Jyh-Cheng Yu

  18. Robust parameter design of micro-injection molded gears using a LIGA-like fabricated mold insert

    Article • Journal of Materials Processing Technology, August 2009, Elsevier

    Distinguished Professor Jyh-Cheng Yu

  19. Chemical Reactions During Wet-Etching Process of LSMO/PZT/LSMO-Structured Device Fabrication

    Article • Ferroelectrics, June 2009, Taylor & Francis

    Distinguished Professor Jyh-Cheng Yu

  20. Compatibility of Material Processing and Fabrication of Sol-Gel Derived PZT Based Devices

    Article • Ferroelectrics, June 2009, Taylor & Francis

    Distinguished Professor Jyh-Cheng Yu

  21. Design and System Modeling of a Tri-Axial Microaccelerometer Using Piezoelectric Thin Films

    Article • Ferroelectrics, January 2009, Taylor & Francis

    Distinguished Professor Jyh-Cheng Yu

  22. Sensing liquid density using resonant flexural plate wave devices with sol–gel PZT thin films

    Article • Microsystem Technologies, May 2008, Springer Science + Business Media

    Distinguished Professor Jyh-Cheng Yu

  23. Sensing liquid density using resonant flexural plate wave devices with sol–gel PZT thin films

    Article • Microsystem Technologies, February 2008, Springer Science + Business Media

    Distinguished Professor Jyh-Cheng Yu

  24. Evolutionary Engineering Optimization Using Recursive Regional Neural Network and Genetic Algorithm

    Article • September 2007, Institute of Electrical & Electronics Engineers (IEEE)

    Distinguished Professor Jyh-Cheng Yu

  25. Structure representation for concurrent analysis of product assembly and disassembly

    Article • Expert Systems with Applications, November 2006, Elsevier

    Distinguished Professor Jyh-Cheng Yu

  26. The structure representation for the concurrent analysis of product assembly and disassembly

    Article • January 2005, Institute of Electrical & Electronics Engineers (IEEE)

    Distinguished Professor Jyh-Cheng Yu

  27. Optimization of extrusion blow molding processes using soft computing and Taguchi’s method

    Article • Journal of Intelligent Manufacturing, October 2004, Springer Science + Business Media

    Distinguished Professor Jyh-Cheng Yu

  28. Performance Optimization of Extrusion Blow Molded Parts Using Fuzzy Neural-Taguchi Method and Genetic Algorithm

    Article • January 2002, ASME International

    Distinguished Professor Jyh-Cheng Yu

  29. System modeling of microaccelerometer using piezoelectric thin films

    Article • Sensors and Actuators A Physical, February 2001, Elsevier

    Distinguished Professor Jyh-Cheng Yu

  30. Design and fabrication of the micro-accelerometer using piezoelectric thin films

    Article • Ferroelectrics, January 2001, Taylor & Francis

    Distinguished Professor Jyh-Cheng Yu

  31. Modified Sequential Programming for Feasibility Robustness of Constrained Design Optimization

    Article • September 2000, ASME International

    Distinguished Professor Jyh-Cheng Yu

  32. Design for Robustness Based on Manufacturing Variation Patterns

    Article • Journal of Mechanical Design, June 1998, ASME International

    Distinguished Professor Jyh-Cheng Yu

  33. DESIGN OPTIMIZATION FOR ROBUSTNESS USING QUADRATURE FACTORIAL MODELS

    Article • Engineering Optimization, March 1998, Taylor & Francis

    Distinguished Professor Jyh-Cheng Yu

  34. Process selection for the design of Aluminum components

    Article • August 1993, ASME International

    Distinguished Professor Jyh-Cheng Yu

  35. Computer-aided design for manufacturing process selection

    Article • Journal of Intelligent Manufacturing, June 1993, Springer Science + Business Media

    Distinguished Professor Jyh-Cheng Yu

  36. Process selection for the design of aluminum components

    Article • Advances in Engineering Software, January 1993, Elsevier

    Distinguished Professor Jyh-Cheng Yu