All Stories

  1. A5356 cladding layer formation on a SUS304 plate by a weaving strategy with wire-arc directed energy deposition
  2. Achieving high productivity in wire-arc directed energy deposition of magnesium alloy thin-walled structures via active cooling
  3. Microstructural variation and mechanical behavior of Inconel 718/Stellite 6 functionally graded materials fabricated by wire-arc directed energy deposition
  4. Engineering a Sustainable CeO2 Nanoparticle-Enhanced Coconut Oil-Based Cutting Fluid: Tribological Performance in MQL Turning of Ti-6Al-4V
  5. Nanoparticles for the prominent Tribological and rheological properties of greener metalworking fluids – A review
  6. Influence of electrode rotation speed on geometry and internal structure of weld beads in rotary TIG wire-arc-directed energy deposition
  7. ERTi-2 cladding layer formation on a 5052 plate by a weaving strategy with wire and arc additive manufacturing
  8. Block processing time-based programming for high-speed, high-precision 5-axis machining
  9. Influence of Reverse Finishing on Characteristics of Drilling Surface
  10. Special Issue on Advanced Metal Cutting Technologies
  11. Welding torch with coaxial wire feed and rotating electrode for wire-arc directed energy deposition
  12. Introduction of Internal Circulation-Based Cooling Methods and Green Coolants in Milling via Cutting Tool and Tooling Design
  13. Effect of arc length on deposition characteristics in rotary tungsten inert gas (TIG) torch
  14. Internal coolant circulation-based tool design to reduce the temperature and heat spreading when turning SUS304 Stainless Steel
  15. Characteristics of Coconut Fibre Combined with Vinyl Ester Composites Through Material Testing and Machining
  16. Effects of internal coolant circulation-based cooling schemes on tool wear in turning SUS304 stainless steel
  17. Development of directed energy deposition strategy for a mechanically interlocked pure Ti and Al alloy component with cross-shaped internal pure Ti lattice
  18. Development of Electrodeposited Wire Mesh Grinding Wheel for Cutoff and Grooving Carbon Fiber Reinforced Plastic
  19. Special Issue on Recent Trends in Additive Manufacturing
  20. Effect of tool posture on chatter vibration in turn-milling
  21. Microstructure Evaluation of the Potential of Additive Manufactured Dissimilar Titanium–Aluminum Alloys
  22. Characteristics of Pinewood Dust Combined with Vinyl Ester Composites Through Material Testing and Machining
  23. Investigation of the Microstructure of Ti6Al4V Alloy by Coaxial Double Laser Metal-Wire Deposition
  24. Mechanism to suppress regenerative chatter vibration due to the effect of air-cutting and multiple regeneration during low frequency vibration cutting
  25. Ultra-Fine Bubbles (UFB) Inserted Novel Coconut Oil Based Metal Working Fluid (MWF) As a Sustainable Lubricant for Turning of Ti-6Al-4V
  26. Development of In-Process Temperature Measurement of Grinding Surface with an Infrared Thermometer
  27. Evaluating surface quality by luminance and surface roughness
  28. Improvement of Cooling Effect and Dimensional Accuracy of Wire and Arc Additive Manufactured Magnesium Alloy by Active-Cooling-Based Contacting Copper Blocks
  29. Residual stress fluctuates periodically via the workpiece rotation phase during low frequency vibration cutting
  30. Wire Arc Additive and High-Temperature Subtractive Manufacturing of Ti-6Al-4V
  31. Recent advances on high performance machining of aerospace materials and composites using vegetable oil-based metal working fluids
  32. Rake angle effects on ultrasonic-assisted edge trimming of multidirectional CFRP laminates
  33. Experimental Investigations Towards Hole Accuracy in Micro-drilling of Carbon Fibre Reinforced Polymer Material
  34. FEM Simulation on Cutting Process
  35. Effects of the size of built-up layer on the wear of cemented carbide tools in cutting of SUS304 stainless steel
  36. Simulating the build shape for a shell structure for wire and arc additive manufacturing using the bead cross-section model
  37. Thermal sensing and heat input control for thin-walled structure building based on numerical simulation for wire and arc additive manufacturing
  38. Performance Evaluation of White Coconut Oil Based Metal Working Fluid (MWF) Under Minimum Quantity Lubrication (MQL) for Machining of Inconel 718 and AISI 304
  39. Green Metalworking Fluids for sustainable machining applications: A review
  40. Determining the effect of tool posture on cutting force in a turn milling process using an analytical prediction model
  41. Development of a cooperative system for wire and arc additive manufacturing and machining
  42. Surface quality evaluation of 0.2 % C and AISI 304 steels in turning with sustainable lubricating condition
  43. Effect of the Type of Grinding Wheel on the Surface Characteristics of a Titanium Alloy with Internal Coolant Supply
  44. Surface Characteristics with Curved Grinding of a Titanium Alloy with Coolant Supplied from the Inner Side of the Grinding Wheel
  45. Layer geometry control for the fabrication of lattice structures by wire and arc additive manufacturing
  46. Application of a novel woven metal wire tool with electrodeposited diamond grains for carbon fiber reinforced plastics core drilling
  47. Machining performance of vegetable oil with phosphonium- and ammonium-based ionic liquids via MQL technique
  48. Precise additive fabrication of wall structure on thin plate end with interlayer temperature monitoring
  49. Control of the chemical composition distribution in deposited metal by wire and arc-based additive manufacturing
  50. Method for generating CNC programs based on block-processing time to improve speed and accuracy of machining curved shapes
  51. Method to evaluate speed and accuracy performance of CNC machine tools by speed-error 2-D representation
  52. The influence of modified vegetable oils on tool failure mode and wear mechanisms when turning AISI 1045
  53. Material-property evaluation of magnesium alloys fabricated using wire-and-arc-based additive manufacturing
  54. Oscillating Finish Grinding of CFRP with Woven Metal Wire Tool Utilizing Plunger Pump Pulsation
  55. Chip control in turning with synchronization of spindle rotation and feed motion vibration
  56. CFRP machining capability by a circular saw
  57. Effect of Tip Shape of Frictional Stir Burnishing Tool on Processed Layer’s Hardness, Residual Stress and Surface Roughness
  58. High performance machining of carbon fiber-reinforced plastics
  59. Real-time grinding state discrimination strategy by use of monitor-embedded grinding wheels
  60. A method for the evaluation and magnified representation of two-dimensional contouring error
  61. Chip Adhesion and Tool Wear in Driven Rotary Cutting of Stainless Steel
  62. The effect of oil mist supply on cutting point temperature and tool wear in driven rotary cutting
  63. Evaluation of modified jatropha-based oil with hexagonal boron nitride particle as a biolubricant in orthogonal cutting process
  64. Performance of palm oil as a biobased machining lubricant when drilling inconel 718
  65. Prediction of drilling temperature during low-frequency vibration drilling of titanium alloy
  66. Study on Wire and Arc-based Additive Manufacturing
  67. Identification of Aluminum Alloy Flow Stress to Determine FEM Analysis Constitutive Equation for Machining Material
  68. Effect of low frequency vibration applied to feed direction on turning process
  69. Dissimilar metal deposition with a stainless steel and nickel-based alloy using wire and arc-based additive manufacturing
  70. Development of In-Process Monitoring System for Grinding Wheel Surface Temperature and Grinding State
  71. Improvement of Surface Roughness with Micro-Axial Vibration of Spindle by Pressure Pulsation of Grinding Fluid Supplied through inside of Wheel
  72. Cutting Forces Analysis in Additive Manufactured AISI H13 Alloy
  73. An Integral Method to Determine Workpiece Flow Stress and Friction Characteristics in Metal Cutting
  74. Development of In-Process Monitoring System for Grinding Wheel Surface Temperature and Grinding State
  75. Improvement of Surface Roughness with Micro-Axial Vibration of Spindle by Pressure Pulsation of Grinding Fluid Supplied through inside of Wheel
  76. Effect of Cutting Conditions on Tool Wear in Driven Rotary Cutting of Maraging Steel
  77. Mechanical Properties Evaluation of Metal Components Repaired by Direct Metal Lamination
  78. Identification of Friction Characteristics and Flow Stress of 0.45% Carbon Steel during Cutting Process
  79. Development of High-speed Shearing Method to Obtain Flow Stress under High Strain Rate
  80. Development of the shell structures fabrication CAM system for direct metal lamination using arc discharge-lamination height error compensation by torch feed speed control-
  81. Frictional stir burnishing on double helical path to satisfy both high hardness and compressive residual stress
  82. 薄板加工におけるびびり振動抑制用動吸振器の設計方法に関する研究
  83. Surface grinding of carbon fiber reinforced plastic (CFRP) with an internal coolant supplied through grinding wheel
  84. Form Accuracy of Internal Grinding of Small and Deep Holes with Coolant Supplied from Inner Side of Grinding Wheel
  85. Effect of Coolant Supplied through Grinding Wheel on Residual Stress of Grinding Surface
  86. Identification of Flow Stress Applicable for FEM Simulation of Orthogonal Cutting Process
  87. FEM Simulation on the Effect of Cutting Parameters in the Driven Rotary Cutting
  88. Free-form curves cutting using flexible circular saw
  89. Temperature measurement of cutting tool and machined surface layer in milling of CFRP
  90. アーク放電を用いた溶融金属積層による造形物の強度
  91. Generation of Regularly Aligned Curved Surface Patches on Free-Form Surface for Patch Division Milling
  92. Temperature Measurement of Surface Grinding Using a Fluid Supplying System from inside of Grinding Wheel
  93. Experimental Study of Helical Milling on CFRP (Carbon Fibre Reinforced Polymer) for the Hole Making Process
  94. Hole Making Process of Carbon Fiber Reinforced Polymer (CFRP) Using End Mill Cutting Tool
  95. Residual Stress and Deformation After Finishing of a Shell Structure Fabricated by Direct Metal Lamination Using Arc Discharge
  96. Study on the Machining of Iron-Based Thermal Spray Coating for Sleeveless Engine Cylinder
  97. Preface
  98. Curved-Line Cutting Using a Flexible Circular Saw
  99. Generation of Hardened Structure on 0.45%C Steel by Frictional Stir Burnishing
  100. Influence of the Cooling Method of the Molten Pool on the Laminating Characteristics in Direct Metal Lamination by Using Arc Discharge
  101. Minimization of Grinding Fluid by Employing the Supplying System from Inner Side of Grinding Wheel and its Effect
  102. Study on Manufacturing Process of Trimming Edge of Stamping Die Tool (Direct Metal Lamination on NC Machine and the Development of Weld Metal)
  103. Study on the Effect of Fabrication Parameters on Strength and Metallographic Structure on Direct Metal Rapid Fabrication Using Arc Welding
  104. Investigation of tool wear and surface integrity on MQL machining of Ti-6AL-4V using biodegradable oil
  105. AN ANALYSIS OF SURFACE INTEGRITY WHEN DRILLING INCONEL 718 USING PALM OIL AND SYNTHETIC ESTER UNDER MQL CONDITION
  106. A study of the effect of palm oil as MQL lubricant on high speed drilling of titanium alloys
  107. Profile Grinding of Difficult-to-Cut Materials Using a Coolant Supplying System from Inside of Grinding Wheel
  108. Fabrication of Elbow Pipe by Direct Metal Lamination Using Arc Discharge While Maintaining the Molten Pool in a Horizontal Position
  109. Surface Integrity in MQL Drilling Nickel-Based Superalloy
  110. Investigation on the Cutting Process of Plasma Sprayed Iron Base Alloys
  111. Thermal Behavior and Tool Failures on Rotary Cutting of Difficult-to-Cut Materials Utilizing Multi Tasking Lathe
  112. Effect of Machining Parameters and MQL Liquids on Surface Integrity of High Speed Drilling Ti-6Al-4V
  113. Effect of MQL Liquids on Surface Integrity when High Speed Drilling Titanium Alloy
  114. Surface Integrity when Drilling Nickel-Based Superalloy under MQL Supply
  115. Temperature History and Metallographic Structure of 0.45%C Steel Processed by Frictional Stir Burnishing
  116. Generation of Geometric Pattern in Arbitrary Triangle Patches by Using Patch Division Milling
  117. High Speed MQL Drilling of Titanium Alloy using Synthetic Ester and Palm Oil
  118. Effect of dynamic response and displacement/stress amplitude on ultrasonic vibration cutting
  119. Microscopic phase-dependent residual stresses in the machined surface layer of two-phase alloy
  120. Prediction and Avoidance of Chatter in Milling of Thin-Walled Structure
  121. Application of Minimum Quantity Lubrication when Drilling Nickel-Based Superalloy at High Cutting Speed
  122. Application of Minimum Quantity Lubrication when Drilling Nickel-Based Superalloy at High Cutting Speed
  123. Prediction and Avoidance of Chatter in Milling of Thin-Walled Structure
  124. Analytical Prediction of Thermal Expansion and Residuak Stress on Sequential Cutting Process(<Special Issue>Norms the of Manufacturing and Machine Tools)
  125. Fabrication of an Inclined Wall by the Direct Metal Rapid Fabrication Using an Arc Welding : Factors Affecting on the Accumulated Shape and Its Effects(<Special Issue>Norms the of Manufacturing and Machine Tools)
  126. Prediction and Control of Machining Accuracy in End Milling for Planar Cam
  127. High-speed rotary cutting of difficult-to-cut materials on multitasking lathe
  128. Helical Feed Milling with MQL for Boring of Aluminum Alloy
  129. Effect of Rotary Cutting Tool Posture on Machining Performance utilizing Multi-Tasking Lathe
  130. Study of Simulation of Micro-Cutting Process of Alternatively-Arranged Resin and Metal
  131. Analytical Prediction of Temperature Distribution in Cylinder Liner during Various Boring Operations
  132. Tool Path Generation for the Formation of a Geometric Surface Pattern on a Curved Surface by Patch Division Milling
  133. Clarification of the Amount of Machining Error Resulting from the Cutting Force and Thermal Expansion during the Cylinder Liner Boring Process
  134. Generation of a regularly aligned surface pattern and control of cutter marks array by patch division milling
  135. Investigation of thermal behavior on cylinder liner during its boring process
  136. Influence of Acceleration/Deceleration of Translational Axes and Spindle Speed Deviations on Cutter Mark Array
  137. 姿勢制御電極による電解曲がり穴加工
  138. Low-Frequency Vibration Drilling of Titanium Alloy
  139. Development of Cutting-Burnishing Combined Tool and Its Basic Performance
  140. Effect of Sequential Cuts of Affected Layer in Machining of Two Phase Alloy
  141. Study on Prediction and Avoidance of Chatter in Milling Process with CAD/CAE and Impulse Sound
  142. Diffusion and Collection of Mist/Oil-Smoke in Near-Dry Machining Environment
  143. Study on Heat Transfer around End Mill under High Rotation Speed
  144. Generation of Geometric Pattern on Plane Surface by Patch Division Milling
  145. Principal Factors Affecting the Sub-Micrometer Grooving Mechanism of SiC Thin Layers by a 355 nm UV Laser
  146. Development of a layered manufacturing system using sheet metal-polymer lamination for mechanical parts
  147. The effect on fatigue life of residual stress and surface hardness resulting from different cutting conditions of 0.45%C steel
  148. Control of the Residual Stress within a Machined Surface using a Tool for Compressive Residual Stress Generation
  149. 有限要素法による切削シミュレータの開発
  150. Cutting Mechanism on Ultrasonic Vibration Cutting (3rd Report)
  151. Visualization and Analysis of Chip Ejection Process in Dry Drilling of Aluminum alloy
  152. Development of an Layered Manufacturing System Using Sheet Metal-Polymer Lamination and Mounting on a Machining Center
  153. Development of a new tool to generate compressive residual stress within a machined surface
  154. Prediction model of surface residual stress within a machined surface by combining two orthogonal plane models
  155. Control of the Mechanical Property on Machined Surface by a New Tool for Cutting-Burnishing Combined Process
  156. Cutting Mechanism on Ultrasonic Vibration Cutting (1st Report)
  157. Cutting Mechanism on Ultrasonic Vibration Cutting (2nd Report)
  158. Development of the Compressive Residual Stress Generating Cutter and Its Basic Performance
  159. Effect on Fatigue Life of Residual Stress and Surface Hardness Induced by Turning Operation
  160. 振動切削過程における振動と加工零囲気の影響(50Hz振動切削の場合)
  161. MQLを適用したヘリカル送りミリングによるアルミニウム合金の穴加工
  162. Optimization of Cutting Conditions by Combination of Analytical Approach and Database
  163. FEM Analysis of Dynamic Cutting Process
  164. FEM Simulation on Machined Surface Generation in Shaving Process.
  165. Effects of Oil-Mist Supply on Tool Wear at High-Speed Milling.
  166. 10.1299/kikaic.78.2243
  167. FEM Simulation on Cutting Process of Two Phase Alloys.
  168. Application of Computational Machining Method to Discontinuous Chip Formation
  169. FEM analysis of cutting sequence effect on mechanical characteristics in machined layer
  170. 切削工程による加工変質層の推移と制御
  171. The Effect of Non-Linearity of Dynamic Cutting Process upon Self-Excited Chatter Vibration (4th Report)
  172. The Analytical Prediction of the Characteristics within Machined Surface Layer (Part 3)
  173. The Analytical Prediction of the Characteristics within Machined Surface Layer (1st Report)
  174. Finite Element Analysis on Discontinuous Chip Formation.
  175. 自励びびり振動における動的切削過程の非線形効果(第3報)
  176. FEM Analysis on Three Dimensional Cutting. Analysis on Large Deformation Problem of Tool Entry.
  177. Finite Element Approach to Chip Breaker.
  178. The Effects of Non-Linearity of Dynamic Cutting Process upon Self-Excited Chatter Vibration (2nd Report)
  179. 自励びびり振動における動的切削過程の非線形効果 (第1報)
  180. Analysis of Tool Temperature in High-speed Milling